1 ch relay module rf transceiver RF 433 Mhz 220V

1 ch relay module rf transceiver RF 433 Mhz

Details :

Input voltage: 220V

• Receiver sensitivity: > 97 dbm

• Transmission distance: >100m (open space)

• Decoding mode: MCU software decoding

• Remote storage: 20

• Support remote control type: learning code EV1527

• Operating mode: Momentary, toggle, timed lock (5s, 10s, 15s)

• Output terminal: NO, NC, COM

• PCB dimension: 35x30x18mm (L, W, H)

• Remote control battery: 2x3 V CR2016 button batteries

Note: Maximum input power is 220V

Remote programming

Operating mode:

1. Thumb mode: press the remote control the relay will connect and then release the remote control to disconnect the relay;

2. Self-locking mode: press the remote control the relay will connect, then press the remote control again to disconnect the relay;

3. Lock mode: press remote control key A to connect the relay, and press remote control key B to disconnect the relay.

4. Delay mode: press the remote control, the relay will connect, release the remote control and start timing. After 5S, 10S and 15S(3 gears), the relay will be automatically closed.

Learning methods:

1. Learning method:

Press the pairing button on the control panel once, and the LED light will flash once. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

2. Self-locking learning method:

Press the pairing button on the control panel twice, and the LED indicator will flash twice. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

3. Mutual lock learning method:

Press the pairing button on the control panel three times, and the LED indicator will flash three times. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

4.5S Delay learning method:

Press the pairing code button on the control panel four times, and the LED indicator will flash four times. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

5. 10S Delay learning method:

Press the pairing code button on the control panel five times, and the LED indicator will flash five times. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

6. 15S Delay learning method:

Press the pairing button on the control panel six times, and the LED indicator will flash six times. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

ClearIngmethod:

Press the pairing code button on the control panel eight times, then it will automatically erase all learned remote controls. After erasing, the remote control has already learned Can no longer be used

• Receiver sensitivity: > 97 dbm

• Transmission distance: >100m (open space)

• Decoding mode: MCU software decoding

• Remote storage: 20

• Support remote control type: learning code EV1527

• Operating mode: Momentary, toggle, timed lock (5s, 10s, 15s)

• Output terminal: NO, NC, COM

• PCB dimension: 35x30x18mm (L, W, H)

• Remote control battery: 2x3 V CR2016 button batteries

Note: Maximum input power is 220V

Remote programming

Operating mode:

1. Thumb mode: press the remote control the relay will connect and then release the remote control to disconnect the relay;

2. Self-locking mode: press the remote control the relay will connect, then press the remote control again to disconnect the relay;

3. Lock mode: press remote control key A to connect the relay, and press remote control key B to disconnect the relay.

4. Delay mode: press the remote control, the relay will connect, release the remote control and start timing. After 5S, 10S and 15S(3 gears), the relay will be automatically closed.

Learning methods:

1. Learning method:

Press the pairing button on the control panel once, and the LED light will flash once. After the LED indicator is on, press the button You need to pair the remote control, indicates it ur LED on the control panel will flash 3 times which means pairing is successful.

2. Self-locking learning method:

Press the pairing button on the control panel twice, and the LED indicator will flash twice. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

3. Mutual lock learning method:

Press the pairing button on the control panel three times, and the LED indicator will flash three times. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

4.5S Delay learning method:

Press the pairing code button on the control panel four times, and the LED indicator will flash four times. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

5. 10S Delay learning method:

Press the pairing code button on the control panel five times, and the LED indicator will flash five times. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

6. 15S Delay learning method:

Press the pairing button on the control panel six times, and the LED indicator will flash six times. After the LED indicator is on, press the button you need to pair the remote control, the LED indicator on the control panel will flash 3 times which means the pairing is successful.

ClearIngmethod:

Press the pairing code button on the control panel eight times, then it will automatically erase all learned remote controls. After erasing, the remote control has already learned Can no longer be used